← All guides

How to Inspect Marble and Granite Slabs Before Shipment

Inspect against an approved reference sample and a written purchase order, not against a perfect ideal. In limestones such as Galala and Sunny, fossil fragments, small natural holes, stylolites and shade movement are normal features, while open cracks, dry seams, crumbling edges and out-of-tolerance thickness or flatness are grounds to reject. Get numbered bundle photos in daylight, measure thickness and flatness, and book any third-party inspection before the slabs are crated.

Why the bundle you get never matches the sample exactly

Slabs are sawn from blocks, and blocks from the same quarry face differ in shade, fossil density and vein pattern; the Egyptian marble types guide covers how far each stone moves. An inspection decides whether that variation stays inside the range you approved, and whether any slab has a fault that will cause trouble in cutting, fixing or use.

The European product standards make the same distinction. EN 1469 (slabs for cladding) and EN 12058 (slabs for floors and stairs) treat colour, veining and texture as something identified by a reference sample supplied by the producer, and they state that visible features such as cracks, inclusions, cavities, stylolites and veins are permitted as long as they are typical of the stone and do not harm its performance. On that reading, a fossil or a vent in Galala only becomes a defect when there are more of them than the reference shows, or when one weakens the slab.

Hairline cracks, dry seams and other marks: what counts as a defect

Agree this vocabulary with your supplier before production. The verdicts below are a starting point; the reference sample and your purchase order decide.

Before anything else, run a fingernail across a linear mark: if it slides over, it is usually a healed fissure or a vein; if it catches in an open gap, treat it as a crack. Then tap the face in a grid with a small hammer or the handle of a screwdriver. A clear ring means sound stone, a dull or hollow note suggests a void, a delamination under mesh, or a crack you cannot see yet.

Stylolites, the toothed seams where clay residues collect, are common in beige limestones sold as marble and usually harmless on a wall. In wet floors the clay can wash out and leave open seams, and stone cut parallel to the bed is more prone to this and to surface spalling. For floors or exteriors, ask for heavily stylolitic slabs to be excluded, or for strength tests taken in two directions.

Common slab marks and how buyers usually treat them
MarkWhat it looks likeUsual verdictHow to check
Hairline or healed fissureFine line following the grain or a vein, closed or filled with crystalNormal if typical of the stone and not crossing the full widthFingernail slides over; slab rings when tapped
Open crackLine with a gap, often cutting across the grainReject, or accept only on resined material with a discount you agreed in writingFingernail catches; shows as a dark line when wetted
Dry seamNatural unhealed fracture, a plane of weakness that may not be visible dryReject on structural pieces such as stairs, overhangs and thin claddingWet the slab, look along the seam at a low angle, tap test
StyloliteWavy, toothed seam, yellow to grey or blackNormal in Galala, Sunny and similar limestones in moderate amountsCompare density against the reference sample
Pinholes, vents, fossil holesSmall cavities, often where shell fragments sitNormal in limestones; usually filled at the factoryAgree on maximum hole size and whether filling is allowed
Iron or rust spotsOrange to brown stains, from iron minerals such as pyrite in the stone or from contact with rusting steelReject if marked on the face of exposed piecesLook for dark mineral grains; check strapping and storage
Edge and corner chipsMissing flakes on arrisesMinor on full slabs that will be cut; reject on finished cut-to-sizeCheck all four edges and corners in the photos
Bowing or warpSlab rocks on a flat surface or shows a gap under a straightedgeReject beyond the agreed flatness toleranceStraightedge along the length and the diagonals

Resin-filled and mesh-backed slabs: acceptable or not?

Filling holes and fissures with resin or cement, and gluing fibreglass mesh to the back of a slab, are normal steps in many factories. EN 1469 and EN 12058 treat patching and filling as part of normal processing, but require the type of treatment and the materials used to be declared, and the reference sample has to show what the fills look like on the finished face. If you need untreated stone, or you only accept epoxy rather than polyester fills, the purchase order is where you say so.

Filled areas often differ slightly in gloss or transparency from the stone around them, and inspectors use a UV lamp because resin tends to fluoresce differently. Badly colour-matched or sunken fills are fair grounds for rejection.

The EN standards say nothing about mesh backing, so any requirement has to come from your order. Mesh backing spreads stress across the back of a fragile slab and slows crack growth in cutting and handling; it does not make a cracked slab sound. Check the mesh for bubbles, lifted edges and hollow spots. Backing adds thickness, and some epoxies are not rated for outdoor or wet exposure, so confirm it with your fixing engineer for exterior cladding. Which treatments are applied varies by stone, lot and factory, so ask your supplier about the material on offer.

First choice, commercial and shade sorting

First choice, commercial (or standard) and second choice are trade grades, but no standard defines them, and two Egyptian factories can use the same word for different selections. Do not rely on the grade name alone. Write down what it means for your order: the shade range, the maximum number and size of filled holes per slab, whether stylolites are acceptable, and how many slabs per bundle may carry visible repairs.

Shade sorting means the factory groups slabs or tiles into lots of similar tone. For Sunny this usually means separating lighter and deeper gold; for Galala, cream depth and fossil density. Ask for each lot to be marked on the crate so the installer can lay one lot per area. For book-matched or sequence-matched walls, the slabs must stay in cutting order and carry consecutive numbers.

When you compare production against the reference, do it the way the EN standards describe: place the reference sample next to the production slabs and look at them from about two metres in normal daylight. Close-up comparisons under workshop lights exaggerate differences that nobody will see once the stone is installed.

What to ask for in bundle photos and video

If you are not flying to Egypt, the photos are your inspection. A useful request covers:

Every slab, face-on, photographed outdoors in daylight or under neutral white light, with the bundle number and slab number written on the edge or on a card in the frame, and the face (front or back) noted. A tape measure laid along the slab in at least one shot per bundle so you can read the real size. Both faces of any slab with mesh, resin or visible marks, plus close-ups of the four corners and edges. A short video walking along the bundle as the slabs are flipped, which shows colour progression and catches slabs that were left out of the stills.

On polished slabs, ask for dry photos, since the polish already shows the colour. On honed, brushed or raw slabs, ask for one photo dry and one with the face wetted: water darkens and deepens the surface roughly the way a colour-enhancing sealer would, so it shows the range of what the finished floor could look like. Wetting also makes fissures and dry seams show briefly as darker lines, though it can make surface scratches look like cracks too, so look dry first and wet only the spots you are unsure about.

Thickness, flatness and gloss: what to measure

Measure thickness with a caliper at the four corners and the middle of each long edge. For finished slabs, EN 1469 and EN 12058 set the tolerances below and let the manufacturer declare tighter ones. Adhesive or thin-bed fixing may need tighter tolerances, so if your installer works that way, order calibrated thickness. For full gangsaw slabs that will be cut again by a fabricator, there is no single trade figure; trade sources quote around ±1 to ±1.5 mm for 2 cm and 3 cm granite slabs, so agree your own number.

Flatness under the same standards must not exceed 0.2% of the slab length and never more than 3 mm. Lay a straightedge along the length and both diagonals. Raking light along the polished face also shows hollows and waves from the polishing line. The same standards define a slab's size as the smallest rectangle that encloses it. Irregular gangsaw slabs are usually invoiced on that gross rectangle rather than on the usable area, so ask how the supplier measures slabs before you compare prices per square metre.

Gloss meters read in gloss units (GU), scaled to a polished black glass reference at 100 GU. The 60° geometry is the usual starting point, with 20° for very high gloss. No standard sets a target for polished marble or granite, and the figures quoted online come from equipment sellers. Take readings on the approved reference slab, write that figure into the order as a minimum, and have the inspector read several points per slab, including near the edges.

If your project is specified to ASTM rather than EN standards, note that the ASTM specifications cover physical properties, not appearance. ASTM C503 covers marble and C615 granite, while Galala, Sunny and the other Egyptian beiges, being limestones, fall under ASTM C568. These set requirements for absorption, density, compressive and flexural strength and abrasion resistance, which you check with lab test reports, not with a slab inspection.

Dimensional tolerances for finished slabs (EN 1469:2015 and EN 12058:2015)
Nominal thicknessToleranceExample
Over 12 mm up to 30 mm±10%20 mm slab: 18 to 22 mm
Over 30 mm up to 80 mm±3 mm40 mm step: 37 to 43 mm
Over 80 mm±5 mm100 mm block step: 95 to 105 mm
Length and width, sawn edges, under 600 mm±1 mm up to 50 mm thick; ±2 mm over 50 mm300 mm tile: 299 to 301 mm
Length and width, sawn edges, 600 mm and over±1.5 mm up to 50 mm thick; ±3 mm over 50 mm1,200 mm slab: 1,198.5 to 1,201.5 mm
Flatness (all faces except natural cleft)Max 0.2% of length, never over 3 mm1,200 mm tile: 2.4 mm max

When to book a third-party inspection and what to write in the purchase order

Book the inspection after polishing and before crating. Once slabs are strapped into A-frames or closed crates, an inspector sees little more than the outer slabs, and reopening crates costs time at the factory. A pre-shipment inspection covers the product itself: slab-by-slab or sample-based checks of size, thickness, finish and defects, against the purchase order and the reference. A container loading check happens during loading and covers quantities, packing, dunnage and container condition; inspection firms say it does not replace the pre-shipment inspection. For large tile orders, inspectors sample to a plan such as ANSI/ASQ Z1.4, so agree the acceptance level in advance.

A purchase order that makes inspection straightforward includes: stone name and the reference sample number you approved; grade and what it means (shade range, filling allowed or not, maximum hole size, stylolites, number of repaired slabs per bundle); finish, plus a minimum gloss reading if polished; nominal size and thickness with tolerances, or calibrated thickness for tiles; whether resin, mesh backing or other treatments are accepted and which type; shade lots marked on each crate; slab numbering and sequence for matched pieces; photo and video requirements before shipment; the inspection stage and who carries it out; and what happens with rejected pieces (replace, credit or discount).

Pay the balance after you have either the inspector's report or a full set of numbered photos that match the packing list. For packing and container loading, see packing and shipping, and for the wider ordering process read how to import marble from Egypt. If you want to agree a reference sample, grading terms or a photo protocol for your order, contact us.

Stones in this guide

Related guides

Need sizes, finishes or a quote? Contact us.